Installation Guide

1 Important note
2 Identifying device
3 Download speed camera data
4 Preparing USB flash drive
5 Installation of speedcam data on navigation device
6 Updating speed camera data
7 Removing speed camera data
8 Frequently Asked Questions

 

Hi there.

Are you a native speaker? Would you be willing to help us?
We are very appreciative of translations or pictures/screenshots to help optimize our installation guide. Or any other advice.
Please don't hesitate to write us an email: info@scdb.info. Thanks in advance.

 

1 Important note

    We recommend to use a Windows computer for the installation.

    Mac computers write additional service files on the USB flash drive. It doesn't work with these files.
    Therefore you should clear the USB flash drive with the free application CleanMyDrive 2 before connecting to the navigation device.

 

2 Identifying device

    First, check and identify your device if it was really produced by manufacturer Harman/Becker.
    Does your Peugeot WIP COM 3D (NG4) looks like in that picture?

    Take also a look to software version (press Setup key > System > Software version).

    You can only use the database with the shown device above.
    Devices produced by manufacturer Magneti Marelli are not supported (RT3, RT4, RT5, RT6, WIP COM, WIP Nav+, Connect Nav+, SMEG, SMEG+).

    Identify your device before purchase. Refund excluded after download started of full database.

 

3 Download speed camera data

  1. Go to our product page for Peugeot WIP COM 3D.
    We offer only data of fixed speed cameras.
    Press button Download.

  2. Save the file peugeot-wipcom.zip on your hard disc.

    Note: In most cases, the file is saved directly to the download folder of the computer.
    Depending on your browser settings, sometimes you can choose the save location by yourself.

  3. Unpack the zip file.
    Unpacking on a Windows computer: right-klick on the zip file > Extract all...

  4. You get the folder pkgdb and the file config.nfm.

 

4 Preparing USB flash drive

  1. Connect an USB flash drive to the computer.

  2. Reformat the USB flash drive as FAT32 (not: FAT/FAT16 or exFAT).
    Do not use the quick format.
    Reformat as FAT32 before using is strictly recommended.

    Important note: Always reformat, even if you have newly purchased the USB flash drive.

  3. Copy and paste the folder pkgdb and the file config.nfm into the root directory of the USB flash drive.
    Now it should look like this on your USB flash drive:

  4. Safely remove the USB flash drive from the computer.

 

5 Installation of speedcam data on navigation device

  1. Connect the USB flash drive to the WIP COM 3D device.

  2. Press NAV key on the device.

  3. Open the menu Navigation menu > Settings > Update Personal POI.
    Choose the USB as data source.
    Import new Personal POI.

  4. Reboot the device.

  5. Press again NAV key.

  6. Go to Navigation menu > Settings > Set parameters for risk areas.

  7. Enable all options: Show on map, Visual alert and Audible alert.

  8. Our speedcams files work with a direction of travel dependent warning function. You only get alerts if the radar trap oversees your current driving direction.

 

6 Updating speed camera data

    Repeat all steps of the guide above to update speed cameras in your device.
    We recommend to update the data once a month to drive safely.

 

7 Removing speed camera data

    Download that file to remove speed camera data from your WIP COM 3D device.

    Download Remove-this-file

    Install that file according to the installation guide above.

 

8 Frequently Asked Questions

    We also recommend to note the Frequently Asked Questions. In most cases, the solution to a problem can already be found here.

Good Reasons for SCDB.info - Speed Camera DataBase